Explore the Pulling Tools that are available for rent and full tool details.

Have questions? Reach out to our tool specialists today at (845) 554-6508 or fill out the form below.

Greenlee Cable Pulling Package (6906)

2 Speed Ultra Tugger (UT10-2S) is a one-stop-shop: The only 2 speed puller on the market that can shift from high speed/low load pulling to low speed/high load pulling with a simple double tap motion on the foot pedal control switch. See Product Spec Sheet

• Prime Mover Specification: Required Rope: 7/8" diameter, double-braided, polyester composite Average Breaking Strength: 143 kN (32,000 lb) minimum
• Capacity: The no-load low speed is 9 FT/MINT and can be used on loads up to 8000 LB where the speed will be 6 FT/MINT, or a momentary peak capacity of 10000LB
• Load: 0 - 6500.000 LB (0 - 28.900 KN) Continuous Operation, 6500.000 - 8000.000 LB (28.900 - 35.600 KN) 15 Minutes ON/15 Minutes OFF, 8000.000 - 10000.000 LB (35.600 - 44.500 KN) Momentary

Maxis Cable Puller (XD10)

The Maxis® XD10 EXTREME Duty Cable Puller is designed to get the job done, thriving in the most extreme pulling conditions, allowing you to pull faster and safer up to 10,000 lbs.

• Specifications: 40in (h) x 26in (w) x 70in (d)
• Capacity: 6,500lbs +

Greenlee Tugger (G3)

High-speed cable puller pulls up to 1000 lbs (97f/min) with a 25% stronger continuous pulling load.

• Speed: Pulling Rope : 1/2 IN Polyester (10000 LB Minimum Breaking Strength), 00444 - Foot switch
• Prime Move Specification: 1/2" double-braided composite rope 10,000 lb average breaking strength

Greenlee Tugger (G6)

G6 TURBO™ 6000 LB Cable Puller can be set up in less than 60 seconds. With two speed motor specially designed for 6,000 pound pulls, it also has dual capstans to increase pulling speeds and maximize efficiency. See Product Spec Sheet

• Pulling Rope: 3/4” (19.1 mm) Double-Braided Composite, Rated at 26000 LB
• Pulling Force: 4000 LB Continuous, 5000 LB Intermittent, 6000 LB Momentary

iTool Wire Puller (C12K)

The fully self-contained, compact design of the Cannon 12K™ wire puller features the only speed reversible motor that is sure to get even the heaviest pulls done in record time. The Cannon 12K™ is the only 12,000 lb. wire puller that can be attached to the receiver hitch on a truck.

• Specifications: 68”L x 30”W x 57”H (Collapsed) 188”L x 30”W x 57”H (Extended) 404lbs
• Speed: Up to 36’ per minute

Greenlee Cable Feeder (6810)

Feeds cable at variable speeds to match the speed of cable pulling tool while accommodating cable ranging in size up to 3.5 IN (88.9mm) in diameter, with top-loading and end-loading cable loading methods.

• Speed: 4-36 feet per minute. (1.2-11 meters per minute)
• Prime Mover Specification: Tire Pressure Carlisle Turf Glide : 1.5 bar (22 psi) Carlisle USA Trail : 3.8 bar (50 psi)
• Cable Size: 8 x 250 MCM cable 6 x 500 MCM cable 5 x 750 MCM cable
• Capacity: Approximately 11,300 kg (25,000 lb)

Maxis Cable Feeder (MCF-01)

Designed and built specifically to accommodate Southwire® SIMpull® wire, the Maxis® Feeder is a revolutionary way to feed wire quickly and efficiently.

• Specifications: 36in (h) x 43in (w) x 32in (d), 360lbs
• Capacity: Up to 1,000lbs